Lakhasly

?1.?These slides illustrate various aspects of infection control in dental radiography as described in the document.- Cover or disinfect the tubehead, position-indicating device (PID), control panel, and exposure button.- Use plastic or foil barriers on surfaces that are hard to clean, especially on electrical switches.- Use barriers to minimize saliva contamination on film packets.Radiography Operatory Preparation (Slide Fig.- Determine surfaces to be covered or disinfected with high-level disinfectant.- Discard barriers and clean surfaces after the procedure.- Carefully remove contaminated barriers without touching the inner film packet.- Develop a sequence to touch as few surfaces as possible.- Disinfect the work area and place a barrier (e.g., paper sheet, paper towels, or plastic cover).Infection Control During Exposure (Slide Fig.- Wipe each film with a paper towel to remove saliva after removing it from the patient's mouth.X-Ray Machine (Slide Fig.The Work Area (Slide Fig.Film Handling (Slide Fig.40-4) ???2.40-5) ??3.40-6) ???4.40-7) ???5.40-8) ??

‏1. Radiography Operatory Preparation (Slide Fig. 40-4)
‏ - Determine surfaces to be covered or disinfected with high-level disinfectant.
‏ - Use plastic or foil barriers on surfaces that are hard to clean, especially on electrical switches.

‏2. X-Ray Machine (Slide Fig. 40-5)
‏ - Cover or disinfect the tubehead, position-indicating device (PID), control panel, and exposure button.

‏3. The Work Area (Slide Fig. 40-6)
‏ - Disinfect the work area and place a barrier (e.g., paper sheet, paper towels, or plastic cover).
‏ - Discard barriers and clean surfaces after the procedure.

‏4. Film Handling (Slide Fig. 40-7)
‏ - Use barriers to minimize saliva contamination on film packets.
‏ - Carefully remove contaminated barriers without touching the inner film packet.

‏5. Infection Control During Exposure (Slide Fig. 40-8)
‏ - Develop a sequence to touch as few surfaces as possible.
‏ - Wipe each film with a paper towel to remove saliva after removing it from the patient's mouth.

‏These slides illustrate various aspects of infection control in dental radiography as described in the document.

Here are the key points from the document "Infection Prevention in Dental Radiography," along with the slide numbers (figure numbers) where relevant illustrations are provided:

1. 
   

   Radiography Operatory Preparation (Slide Fig. 40-4)

   
   
   
   
   • Determine surfaces to be covered or disinfected with high-level disinfectant.
   
   
   • Use plastic or foil barriers on surfaces that are hard to clean, especially on electrical switches.
   
   
   
   


2. 
   

   X-Ray Machine (Slide Fig. 40-5)

   
   
   
   
   • Cover or disinfect the tubehead, position-indicating device (PID), control panel, and exposure button.
   
   
   
   


3. 
   

   The Work Area (Slide Fig. 40-6)

   
   
   
   
   • Disinfect the work area and place a barrier (e.g., paper sheet, paper towels, or plastic cover).
   
   
   • Discard barriers and clean surfaces after the procedure.
   
   
   
   


4. 
   

   Film Handling (Slide Fig. 40-7)

   
   
   
   
   • Use barriers to minimize saliva contamination on film packets.
   
   
   • Carefully remove contaminated barriers without touching the inner film packet.
   
   
   
   


5. 
   

   Infection Control During Exposure (Slide Fig. 40-8)

   
   
   
   
   • Develop a sequence to touch as few surfaces as possible.
   
   
   • Wipe each film with a paper towel to remove saliva after removing it from the patient's mouth.
   
   
   
   

These slides illustrate various aspects of infection control in dental radiography as described in the document.

Slide 9: Preparing the Operatory

•	Identify surfaces: Determine which surfaces need to be covered or disinfected.

•	Use barriers: Apply plastic or foil barriers to surfaces that are difficult to clean, like electrical switches.

Slide 10-13: X-Ray Machine Preparation

•	Cover components: Ensure the tubehead, position-indicating device (PID), control panel, and exposure button are either covered with barriers or disinfected.

•	Disinfection: Use EPA-registered hospital-grade disinfectant for surfaces that are not covered.

Slide 14-18: Work Area Preparation

•	Set up work area: Disinfect the area where x-ray film and film-holding devices are placed during exposure.

•	Use barriers: Place barriers such as paper sheets, paper towels, or plastic covers. After procedures, discard barriers and clean the surfaces.

Slide 19-24: Infection Control During Exposure

•	Avoid contamination: After putting on gloves, touch as few surfaces as possible.

•	Wipe films: After removing films from the patient’s mouth, wipe them with a paper towel to remove saliva.

Slide 25-29: Handling Contaminated Films

•	Contain films: Place wiped films in a disposable container, such as a plastic bag or paper cup labeled with the patient’s name.

•	Transport carefully: The container should not be touched with gloved hands. Transport films to the darkroom only after removing gloves and washing hands.

Slide 30-33: Film-Holding Devices

•	Use disposable or sterilize: Film-holding devices should either be disposable or sterilized/high-level disinfected before reuse.

•	Packaging: Keep sterilized devices packaged until the patient is seated to ensure visible hygiene practices.

Slide 34-37: Post-Exposure Management

•	Discard contaminated items: Dispose of all contaminated items and disinfect any uncovered surfaces.

•	Handwashing: Remove gloves and wash hands after handling contaminated items.

•	Surface disinfection: Use an EPA-registered disinfectant for cleaning exposed surfaces.